We've stumbled on this great article about A Step-by-Step Guide to Installing a Bathtub down the page on the web and figured it made sense to discuss it with you over here.
Mounting a tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, as well as often, tiling skills. Changing an old tub with a new one is likewise a moderately hard job. If the old bathtub is easily available, the project can relocate rapidly; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to move out the old tub and set in the brand-new one. Ensure you have actually certified on your own for the job and fit trying it. Instead of working with a professional to take over a halfway-completed job, it is much better to consider using one before you begin. Chances are you may require a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bathtub in your restroom if you have actually currently bought a new tub and also don't require to change the setup of your previous supply of water pipes.
Your tools and product checklist ought to make up the following:
- New Tub
- Hammer
- Pipeline Wrenches
- Prybar
- Shatterproof glass
- Level
- Pliers
- Adjustable Wrench
- Putty Knife
- Screwdriver
- Cold Chisel
- Measuring tape
- Pipeline Caps
Preparing for the Installation
First of all, the supporting frame provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be quite bothersome due to the restricted gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the needed setting. The wooden boards are valuable in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the bath tub until the level checks out degree.
To set up faucets, fit all-time low of the furthest versatile faucet port to the appropriate supply pipe by making a compression join; then do the very same for the various other faucet.
Switch on the water supply and also examine all joints and brand-new pipework for leakages and tighten them if necessary. Fill up the tub and additionally examine the overflow electrical outlet as well as the normal outlet for leaks.
Finally, fix the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bath tub must wait up until the bath tub has been used at least when as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washers are in location in between the faucet and the sink. Protect the faucet in place with the manufacturer provided backnut. When the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The previous type must be attached to the faucet ends first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a rigid seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in complications with wetness and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can crack fairly very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the marketplace. It is a good idea to fit the tiles using water-resistant or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that editorial about How to Install a Bathtub from an associate on a different blog. Do you know about another individual who is sincerely interested in the topic? Take a moment to share it. We recognize the value of reading our article about How to Install a Bathtub Yourself.
Save time, dial!
Comments on “Plumbing 101: A Guide to Bathtub Installation”